1.     Don't be a dotard!
    Read these "rules" AND introduce
    yourself     before your first post
  2. A healthy approach to understanding measurements
    Being true to what the artists intended
  3. After being asked for the 308th time, Merv lists top 5 headphones
    (opinion / entertainment piece)
    Dismiss Notice
  4. $1000 to the first to design a headamp using discrete components with better measurements than Magni 3+
    Dismiss Notice
IMPORTANT: New Members Read This Don't Be a Measurement Fascist Merv's Top 5 Headphones - 2023 Edition $1000 Challenge

Search Results

Search Again
Page 1 of 3
  1. highflyin9
    Thread

    Octal OTL Aikido-based Tube Headphone Amp

    Finally finished up an interesting build for an Aikido-based OTL headphone amp with enough drive for low impedance cans. The boards are available...
    Thread by: highflyin9, Dec 18, 2018, 1 replies, in forum: DIY
  2. highflyin9
    Post

    Solder and Soldering Irons

    I upgraded to the FX-100 RF earlier this year. Works great, and instant heat up. The only thing I don't like is the iron holder has minimal...
    Post by: highflyin9, Nov 6, 2018 in forum: DIY
  3. highflyin9
    Post

    KORG NuTube Portable Amp Kit

    From memory the NuTekt is warmer than the NuHybrid. Edit: I should add however that the load on the anode is adjustable (and you can swap the...
    Post by: highflyin9, Nov 1, 2018 in forum: DIY
  4. highflyin9
    Post

    KORG NuTube Portable Amp Kit

    So far I've only listened to it with the KEF M500 (albeit for several hours). It was satisfying enough that I didn't have the urge to immediately...
    Post by: highflyin9, Nov 1, 2018 in forum: DIY
  5. highflyin9
    Post

    KORG NuTube Portable Amp Kit

    Good eye. There are four pots on the inside, two are for adjusting the load on the anodes to your preference, two are for gain.
    Post by: highflyin9, Nov 1, 2018 in forum: DIY
  6. highflyin9
    Post

    Audio Guild product roadmap

    What ever happened with Audio Guild? The beautiful looking EMAC 535SE has been sold out for a while now...
    Post by: highflyin9, Oct 31, 2018 in forum: Product Announcements
  7. highflyin9
    Post

    KORG NuTube Portable Amp Kit

    I dug through the manual but did not see anything about power output. In the specs, the output impedance is 10R and recommended load is 15R or...
    Post by: highflyin9, Oct 31, 2018 in forum: DIY
  8. highflyin9
    Post

    KORG NuTube Portable Amp Kit

    That's what floored me, the kit came with a bit of foam damping (not a lot), and the Nutube is mounted off-board. I shook it pretty hard a few...
    Post by: highflyin9, Oct 31, 2018 in forum: DIY
  9. highflyin9
    Thread

    KORG NuTube Portable Amp Kit

    Pete Millett has the latest Korg NuTube Portable Kit from Japan. I did a review at Pete's request but wanted to share here as well just in case...
    Thread by: highflyin9, Oct 31, 2018, 12 replies, in forum: DIY
  10. highflyin9
    Post

    Eddie Current DIY sale

    Dang wish I wasn't on the other side of the U.S.
    Post by: highflyin9, Sep 19, 2018 in forum: DIY
  11. highflyin9
    Post

    Massively overbuilt 45 headphone amp all noise no signal

    I love the "8 pack" of oilers all lined up. The look is definitely old-school muscle :)
    Post by: highflyin9, Sep 19, 2018 in forum: DIY
  12. highflyin9
    Post

    Schiit Loki Mini EQ Released

    I'm very pleased with mine, it's in a secondary system where I swap in/out smaller full range speakers on a Dynaco ST35 and it does a great job...
    Post by: highflyin9, Sep 17, 2018 in forum: Preamps
  13. highflyin9
    Post

    Massively overbuilt 45 headphone amp all noise no signal

    That's a big boy alright. I bet it'll be pushing 60-70 lbs. What AWG metal are you using for chassis?
    Post by: highflyin9, Aug 14, 2018 in forum: DIY
  14. highflyin9
    Post

    Solder and Soldering Irons

    Nicely done! :)
    Post by: highflyin9, Jun 24, 2018 in forum: DIY
  15. highflyin9
    Post

    3.5mm Plugs + Chinese Parts Quality

    I've tried a ton of different ones. Like you I don't care for the telescoping internal soldering tabs, and like yourself I settled on the Amphenol...
    Post by: highflyin9, Jun 19, 2018 in forum: DIY
  16. highflyin9
    Post

    FS: PS Audio and Pangea Power Cords

    ttt
    Post by: highflyin9, Jun 8, 2018 in forum: Closed (Archived) Sales
  17. highflyin9
    Post

    Garage sale of old audio equipment

    The Dynaco PAS with Norman Koren SPICE mod sounds incredibly good, so if that piece of equipment is working it's a real gem.
    Post by: highflyin9, Jun 8, 2018 in forum: Closed (Archived) Sales
  18. highflyin9
    Post

    atomicbob's SMPS Noise Nuke for HP amps with external SMPS

    Very simple and interesting solution. Thinking it might be just what the doctor ordered for the Amp Camp with Meanwell PSU. Looks like Hammond...
    Post by: highflyin9, Jun 8, 2018 in forum: Headphone Amplifier Measurements
  19. highflyin9
    Post

    Recommended XLR Interconnect Cable/Connectors?

    Switchcraft AAA series are my favorite low cost units. They're a 2 piece build and have a nice solid weight and feel. They're harder to source...
    Post by: highflyin9, May 25, 2018 in forum: DIY
  20. highflyin9
    Post

    Pass Labs New DIY "WHAMMY" Headphone Amp

    Got the dual Burson in the mail and dropped it in. I had a single version before hence it wasn't working. The dual works perfectly well and sounds...
    Post by: highflyin9, May 24, 2018 in forum: DIY
Showing results 1 to 20 of 58 Next >
Search Again
Page 1 of 3